__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (May 5 2009 - 18:59:48) Marvell version: 3.4.4 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width [16384kB@f8000000] Flash: 16 MB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PCI 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 3  2  1  0 ## Booting image at 00800000 ... Image Name: Linux-2.6.33.2 Created: 2010-09-27 20:48:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1988336 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................. done, booting the kernel. Linux version 2.6.33.2 (root@BuildEnv-00) (gcc version 4.2.1) #1 Tue Sep 28 04:48:50 CST 2010 CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 CPU: VIVT data cache, VIVT instruction cache Machine: Feroceon-KW ARM Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,115200 root=/dev/ram initrd=0xa00000,0x900000 ramdisk=32768 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 246400KB available (3604K code, 257K data, 136K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:128 Console: colour dummy device 80x30 Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok xor: measuring software checksum speed arm4regs : 726.400 MB/sec 8regs : 538.400 MB/sec 32regs : 618.000 MB/sec xor: using function: arm4regs (726.400 MB/sec) NET: Registered protocol family 16 Feroceon L2: Enabling L2 Feroceon L2: Cache support initialised. CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PEX1_MEM ....no such PEX1_IO ....no such INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_5.1.2)-- DB-88F6281A-BP Soc: 88F6281 A1 LE Detected Tclk 200000000 and SysClk 400000000 MV Buttons Device Load Marvell USB EHCI Host controller #0: cf836800 PEX0 interface detected Link X1 PCI: bus0: Fast back to back transfers disabled mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit] pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe00fffff 64bit] (PCI address [0xe0000000-0xe00fffff] pci 0000:00:01.0: BAR 2: assigned [io 0x1000-0x10ff] pci 0000:00:01.0: BAR 2: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff] bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb raid6: int32x1 66 MB/s raid6: int32x2 76 MB/s raid6: int32x4 83 MB/s raid6: int32x8 70 MB/s raid6: using algorithm int32x4 (83 MB/s) Switching to clocksource kw_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 9216K QNAP RTC initializing.... Initializing RTC is completed. rtc kw_rtc: rtc core: registered kw-rtc as rtc0 RTC registered watchdog_init: succeed to register misc device Init WDT and Active SYSREST if WDT timeout XOR registered 4 channels XOR 2nd invalidate WA enabled MV Buttons Driver Load NetWinder Floating Point Emulator V0.97 (double precision) audit: initializing netlink socket (disabled) type=2000 audit(1287181144.000:1): initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 499 alg: No test for stdrng (krng) io scheduler noop registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A brd: module loaded loop: module loaded serial8250_PIC_init..uartclk = 200000000,baudDivisor = 651,irq = 34 qnap_pic_init: succeed to register misc device tsinfo: create proc systemp successfully tsinfo: create proc systemp successfully Integrated Sata device found IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs Spin up ...(0:0) Spin up ...(0:1) scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter IRQ 9/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs Spin up ...(1:0) Spin up ...(1:1) Spin up ...(1:2) Spin up ...(1:3) Wait 0 seconds to initialize scsi 0. scsi2 : Marvell SCSI to SATA adapter Wait 0 seconds to initialize scsi 1. scsi3 : Marvell SCSI to SATA adapter Wait 5 seconds to initialize scsi 2. scsi4 : Marvell SCSI to SATA adapter Wait 5 seconds to initialize scsi 3. scsi5 : Marvell SCSI to SATA adapter scsi 2:0:0:0: Direct-Access Seagate ST32000542AS CC34 PQ: 0 ANSI: 5 scsi 3:0:0:0: Direct-Access Seagate ST32000542AS CC34 PQ: 0 ANSI: 5 scsi 4:0:0:0: Direct-Access Seagate ST32000542AS CC34 PQ: 0 ANSI: 5 scsi 5:0:0:0: Direct-Access Seagate ST32000542AS CC34 PQ: 0 ANSI: 5 Check proc_name[mvSata]. Check proc_name[mvSata]. sd 2:0:0:0: [sda] Sector size 0 reported, assuming 512. sd 2:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 2:0:0:0: [sda] 0-byte physical blocks Check proc_name[mvSata]. sd 3:0:0:0: [sdb] Sector size 0 reported, assuming 512. sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 3:0:0:0: [sdb] 0-byte physical blocks Check proc_name[mvSata]. sd 4:0:0:0: [sdc] Sector size 0 reported, assuming 512. sd 4:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 4:0:0:0: [sdc] 0-byte physical blocks sd 2:0:0:0: [sda] Write Protect is off Check proc_name[mvSata]. sd 5:0:0:0: [sdd] Sector size 0 reported, assuming 512. sd 5:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 5:0:0:0: [sdd] 0-byte physical blocks sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sda] Sector size 0 reported, assuming 512. sd 2:0:0:0: Attached scsi generic sg0 type 0 Check proc_name[mvSata]. sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: Attached scsi generic sg1 type 0 Check proc_name[mvSata]. sda: sd 5:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: Attached scsi generic sg2 type 0 Check proc_name[mvSata]. sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 3:0:0:0: [sdb] Sector size 0 reported, assuming 512. sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 4:0:0:0: [sdc] Sector size 0 reported, assuming 512. sd 5:0:0:0: Attached scsi generic sg3 type 0 sd 5:0:0:0: [sdd] Sector size 0 reported, assuming 512. sdb:SPI Serial flash detected @ 0xf4000000, 16384KB (64sec x 256KB) Creating 6 MTD partitions on "spi_flash": 0x000000000000-0x000000080000 : "U-Boot" sda1 sda2 sda3 sda4 sdc: sd 2:0:0:0: [sda] Sector size 0 reported, assuming 512. 0x000000200000-0x000000400000 : "Kernel" sdd: 0x000000400000-0x000000d00000 : "RootFS" 0x000000d00000-0x000001000000 : "RootFS2" sd 2:0:0:0: [sda] Attached SCSI disk 0x000000080000-0x0000000c0000 : "U-Boot Config" 0x0000000c0000-0x000000200000 : "NAS Config" sdb1 sdb2 sdb3 sdb4 Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o 2 Giga ports supported o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload (TSO) supported o Large Receive offload (LRO) supported o Receive checksum offload supported o Transmit checksum offload supported o Network Fast Processing (Routing) supported - (Disabled) o Proc tool API enabled o SKB Reuse supported - (Disabled) o SKB Recycle supported - (Disabled) o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o register under mv88fx_eth platform sdc1 sdc2 sdc3 sdc4 sdd1 sdd2 sdd3 sdd4 sd 3:0:0:0: [sdb] Sector size 0 reported, assuming 512. sd 5:0:0:0: [sdd] Sector size 0 reported, assuming 512. sd 4:0:0:0: [sdc] Sector size 0 reported, assuming 512. sd 3:0:0:0: [sdb] Attached SCSI disk o eth0, ifindex = 2, GbE port = 0 sd 5:0:0:0: [sdd] Attached SCSI disk o eth1, ifindex = 3, GbE port = 1 mvFpRuleDb (00000010): 0 entries, 0 bytes Marvell debug tracing is on ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 sd 4:0:0:0: [sdc] Attached SCSI disk ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb: create proc systemp successfully usb: create proc systemp successfully mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@redhat.com usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 5 rtc kw_rtc: setting system clock to 2010-10-15 22:19:34 UTC (1287181174) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 usb 1-1: new high speed USB device using ehci_marvell and address 2 hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected VFS: Mounted root (ext2 filesystem) on device 1:0. Freeing init memory: 136K Start config_util... Start to mirror ROOT part... EXT3-fs (sda1): recovery required on readonly filesystem EXT3-fs (sda1): write access will be enabled during recovery kjournald starting. Commit interval 5 seconds EXT3-fs (sda1): recovery complete EXT3-fs (sda1): mounted filesystem with writeback data mode EXT3-fs (sdb1): recovery required on readonly filesystem EXT3-fs (sdb1): write access will be enabled during recovery kjournald starting. Commit interval 5 seconds EXT3-fs (sdb1): recovery complete EXT3-fs (sdb1): mounted filesystem with writeback data mode EXT3-fs (sdc1): recovery required on readonly filesystem EXT3-fs (sdc1): write access will be enabled during recovery kjournald starting. Commit interval 5 seconds EXT3-fs (sdc1): recovery complete EXT3-fs (sdc1): mounted filesystem with writeback data mode EXT3-fs (sdd1): recovery required on readonly filesystem EXT3-fs (sdd1): write access will be enabled during recovery kjournald starting. Commit interval 5 seconds EXT3-fs (sdd1): recovery complete EXT3-fs (sdd1): mounted filesystem with writeback data mode md: md9 stopped. md: bind md: bind md: bind md: bind raid1: raid set md9 active with 4 out of 4 mirrors md9: bitmap initialized from disk: read 5/5 pages, set 1 bits created bitmap (65 pages) for device md9 md9: detected capacity change from 0 to 542769152 mdadm: /dev/md9 has been started with 4 drives. md9: unknown partition table Mirror of ROOT succeeded. kjournald starting. Commit interval 5 seconds EXT3-fs (md9): using internal journal EXT3-fs (md9): mounted filesystem with writeback data mode Start to mirror RFS_EXT part... config_util: HD1 is TS-NASARM. config_util: HD2 is TS-NASARM. config_util: HD3 is TS-NASARM. config_util: HD4 is TS-NASARM. md: md13 stopped. md: bind md: bind md: bind md: bind raid1: raid set md13 active with 4 out of 4 mirrors md13: bitmap initialized from disk: read 4/4 pages, set 1 bits created bitmap (57 pages) for device md13 md13: detected capacity change from 0 to 469893120 mdadm: /dev/sda4 has been started with 4 drives. md13: unknown partition table config_util: (0) /dev/sda4 size = 458880 Mirror of RFS_EXT succeeded. config_util finished. mount HDD root device kjournald starting. Commit interval 5 seconds EXT3-fs (md9): using internal journal EXT3-fs (md9): mounted filesystem with writeback data mode mount /dev/md9 successful. bootcmd check ok Update Extended rcX_init.d...(1) 4+0 records in 4+0 records out Extract RootFS Ext... kjournald starting. Commit interval 5 seconds EXT3-fs (md9): using internal journal EXT3-fs (md9): mounted filesystem with writeback data mode mountall: mount /dev/md9 successful. kjournald starting. Commit interval 5 seconds EXT3-fs (md13): using internal journal EXT3-fs (md13): recovery complete EXT3-fs (md13): mounted filesystem with writeback data mode install /hd_root_tmp/update_pkg/vim.tgz install /hd_root_tmp/update_pkg/samba.tgz install /hd_root_tmp/update_pkg/libtorrent.tgz install /hd_root_tmp/update_pkg/printer.tgz dev-mapper ready. usbcore: registered new interface driver usblp sysinfo: Module loaded. ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd: driver U82 (Sep 28 2010 05:02:53) LBD=OFF with ioctl loaded at bf072000 NTFS read/write support included Hfs+/HfsX read/write support included RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Slow work thread pool: Starting up Slow work thread pool: Ready eth0: link down eth0: started eth1: started initializing MAC address... eth0: stopped eth0: mac address changed eth0: started MAC_ADDR 00:08:9B:C4:CB:64 eth1: stopped eth1: mac address changed eth1: started MAC_ADDR 00:08:9B:C4:CB:65 storage_boot_init 1 ... eth0: link up, full duplex, speed 1 Gbps kjournald starting. Commit interval 5 seconds EXT3-fs (md9): using internal journal EXT3-fs (md9): mounted filesystem with writeback data mode Checking for bad blocks (read-only test): 0.00% done, 0:00 elapsed 15.66% done, 0:01 elapsed 32.61% done, 0:02 elapsed 50.41% done, 0:03 elapsed 68.17% done, 0:04 elapsed 79.25% done, 0:05 elapsed 94.68% done, 0:06 elapseddone mdadm: /dev/sda2 appears to be part of a raid array: level=raid1 devices=2 ctime=Fri Oct 15 21:30:24 2010 md: bind raid1: raid set md4 active with 1 out of 1 mirrors md4: detected capacity change from 0 to 542769152 mdadm: array /dev/md4 started. md4: unknown partition table Adding 530040k swap on /dev/md4. Priority:-1 extents:1 across:530040k Checking for bad blocks (read-only test): 0.00% done, 0:00 elapsed 17.40% done, 0:01 elapsed 28.86% done, 0:02 elapsed 44.34% done, 0:03 elapsed 60.42% done, 0:04 elapsed 77.89% done, 0:05 elapsed 94.41% done, 0:06 elapseddone md: bind RAID1 conf printout: --- wd:1 rd:2 disk 0, wo:0, o:1, dev:sda2 disk 1, wo:1, o:1, dev:sdb2 md: recovery of RAID array md4 md: minimum _guaranteed_ speed: 5000 KB/sec/disk. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. md: using 128k window, over a total of 530048 blocks. md: bind md: bind readlink: /etc/config: Invalid argument config hidden config directory exist, create symbolic link /etc/config... [OK] Writing model version information... Writing model version info...[OK] sss_convert... log hidden config directory exist, create symboloc link /etc/logs... [OK] Install /mnt/HDA_ROOT/update_pkg/*.qfix ... log hidden config directory exist, create symboloc link /home/sqdatabase... [OK] ln: $/play/ch1/record_nvr_unk/channel1: No such file or directory ln: $/play/ch2/record_nvr_unk/channel2: No such file or directory ln: $/play/ch3/record_nvr_unk/channel3: No such file or directory ln: $/play/ch4/record_nvr_unk/channel4: No such file or directory ln: $/play/ch5/record_nvr_unk/channel5: No such file or directory ln: $/play/ch6/record_nvr_unk/channel6: No such file or directory ln: $/play/ch7/record_nvr_unk/channel7: No such file or directory ln: $/play/ch8/record_nvr_unk/channel8: No such file or directory ln: /home/httpd/cgi-bin/record: File exists ln: /home/httpd/record: File exists xmlcfg_create=0 Start rcv_port: active port 0 :139 active port 1 :445 active port 2 :20 set 139 445 20. /sbin/modagent start Last system shutdown process is incomplete. Starting Disk initialized: Check config files...start No need to do recovery. storage_boot_init 2 ... md: md0 still in use. md: bind md: bind md: bind md: bind raid5: device sda3 operational as raid disk 0 raid5: device sdd3 operational as raid disk 3 raid5: device sdc3 operational as raid disk 2 raid5: device sdb3 operational as raid disk 1 raid5: allocated 67488kB for md0 0: w=1 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0 3: w=2 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0 2: w=3 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0 1: w=4 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0 raid5: raid level 5 set md0 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:sda3 disk 1, o:1, dev:sdb3 disk 2, o:1, dev:sdc3 disk 3, o:1, dev:sdd3 md0: detected capacity change from 0 to 5996376883200 mdadm: /dev/md0 has been started with 4 drives. md: md4: recovery done. RAID1 conf printout: --- wd:2 rd:2 disk 0, wo:0, o:1, dev:sda2 disk 1, wo:0, o:1, dev:sdb2 storage_boot_init.c: Start raid device /dev/md0 successfully md0 : active raid5 sda3[0] sdd3[3] sdc3[2] sdb3[1] md0 : active raid5 sda3[0] sdd3[3] sdc3[2] sdb3[1] md0 : active raid5 sda3[0] sdd3[3] sdc3[2] sdb3[1] md0 : active raid5 sda3[0] sdd3[ md0:3] sdc3[2] sdb3[1] storage_boot_init.c: /dev/ unknown partition table md0 is active. e2fsck 1.41.4 (27-Jan-2009) /dev/md0: recovering journal /dev/md0: clean, 121/365993984 files, 23306518/1463959200 blocks EXT4-fs (md0): mounted filesystem with ordered data mode storage_boot_init.c: check_last_degrade_error... storage_boot_init 6 ... storage_boot_init.c: Checking e-sata: [/sys/block/sdy] Not exist storage_boot_init.c: Checking e-sata: [/sys/block/sdz] Not exist crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory Starting nmbd Services: disabled. killall: snmpd: no process killed Stopping network.../etc/init.d/ipv6.sh: line 50: /proc/sys/net/ipv6/conf/eth0/autoconf: No such file or directory /etc/init.d/ipv6.sh: line 51: /proc/sys/net/ipv6/conf/eth0/accept_ra: No such file or directory /etc/init.d/ipv6.sh: line 50: /proc/sys/net/ipv6/conf/eth1/autoconf: No such file or directory /etc/init.d/ipv6.sh: line 51: /proc/sys/net/ipv6/conf/eth1/accept_ra: No such file or directory Shutting down upnpd services: . eth1: stopped eth0: stopped Stopped. Starting network...eth1 DHCP eth1: started eth0 DHCP eth0: link down eth0: started Start ipchange_notify.sh: ddns disable Shutting down winbindd services: winbindd. Starting winbindd services: disabled. Shutting down bonjour services:cat: /var/lock/bonjour.normal: No such file or directory cat: /var/lock/bonjour.timemachine: No such file or directory mDNSResponderPosix Starting bonjour services: mDNSResponderPosix. Shutting down upnpd services:eth0: link up, full duplex, speed 1 Gbps Start ipchange_notify.sh: ddns disable Shutting down winbindd services: winbindd. Starting winbindd services: disabled. Shutting down bonjour services:cat: /var/lock/bonjour.normal: No such file or directory cat: /var/lock/bonjour.timemachine: No such file or directory mDNSResponderPosix Starting bonjour services: mDNSResponderPosix. Shutting down upnpd services: . . Starting nmbd Services: disabled. killall: snmpd: no process killed Shutting down nvrd services: nvrd. crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory Reconfigure FTP services: Starting nmbd Services: disabled. killall: snmpd: no process killed Shutting down nvrd services: nvrd. route: resolving eth0 crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory Reconfigure FTP services: /etc/init.d/ipv6.sh: line 50: /proc/sys/net/ipv6/conf/eth0/autoconf: No such file or directory /etc/init.d/ipv6.sh: line 51: /proc/sys/net/ipv6/conf/eth0/accept_ra: No such file or directory /etc/init.d/ipv6.sh: line 50: /proc/sys/net/ipv6/conf/eth1/autoconf: No such file or directory /etc/init.d/ipv6.sh: line 51: /proc/sys/net/ipv6/conf/eth1/accept_ra: No such file or directory route: resolving eth0 eth1: stopped ip: RTNETLINK answers: No such process ip: RTNETLINK answers: No such process eth1: started NIC Lan1 Speed: auto eth0: link down eth0: stopped eth0: started eth0: link up, full duplex, speed 1 Gbps /etc/rcS.d/S46ipv6: line 50: /proc/sys/net/ipv6/conf/eth0/autoconf: No such file or directory /etc/rcS.d/S46ipv6: line 51: /proc/sys/net/ipv6/conf/eth0/accept_ra: No such file or directory /etc/rcS.d/S46ipv6: line 50: /proc/sys/net/ipv6/conf/eth1/autoconf: No such file or directory /etc/rcS.d/S46ipv6: line 51: /proc/sys/net/ipv6/conf/eth1/accept_ra: No such file or directory Initializing random number generator... done. Install /mnt/HDA_ROOT/update_pkg/*.qpkg ... Starting thttpd services: thttpd. Starting Qthttpd services: Qthttpd. Starting SMB Services: disabled. Starting FTP services: Start rcv_port: active port 0 :139 active port 1 :445 active port 2 :20 set 139 445 20. proftpd. Starting NFS services: Starting portmapper:rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 . re-export. Starting NFS quotas: rpc.rquotad. Starting NFS mountd daemon: Shutting down NFS mountd: Starting NFS mountd. Mountd port number assigned automatically. Starting NFS daemon: rpc.nfsd NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period Starting NFS lockd status:. Starting ImRd services: crontab: cannot change dir to /var/spool/cron/crontabs: No such file or directory Reconfigure FTP services: Starting periodic command scheduler: crond[1946]: crond 2.3.2 dillon, started, log level 9 crond. [1 0] Detect fake interrupts. [1 0] Fake interrupts detection finished.